What truly makes IR lenses expensive and hard to build are the next few core technologies: F-number, aspheres, coating and athermalization. Each is an optical engineer's nightmare and the real source of a high-end lens's value.
01 F-number: why small-F IR lenses cost more
F-number is roughly the focal length divided by the effective aperture. The smaller the F-number, the larger the aperture and the more IR reaches the detector; at the same focal length, F/1.0 is larger-aperture, F/1.4 smaller, F/2.0 less throughput. For a thermal camera, a small F-number raises system throughput and improves low-contrast performance — more IR, stronger signal, easier NETD. But why expensive? ① Larger aperture means more material — IR materials (Ge, chalcogenide, ZnSe) are costly. ② Harder aberration control — steeper beams make spherical, coma, astigmatic, field-curvature and distortion errors harder. ③ Tighter assembly tolerances — more sensitive to decenter, tilt and spacing. ④ Harder coating and stray-light control. In one phrase: smaller F-number = stronger throughput, but higher cost and manufacturing difficulty.
02 Why IR lenses can't do without aspheres
Spherical lenses are easy to make but optically limited. In IR lenses, aspheres are vital to cut element count, shorten system length and raise image quality. They correct spherical, coma, astigmatism, field curvature, distortion and falling edge quality. For IR, aspheres have another key value: achieving better imaging with fewer elements. Because IR materials are expensive, more elements mean more material, coating, alignment cost and transmission loss; if one asphere replaces several spheres, you cut elements, weight and raise transmission. But aspheres are harder to make — via single-point diamond turning, precision molding, high-precision polishing, replication and follow-up figure metrology. An asphere looks like "a slightly complex curve" but really embodies optics design, ultra-precision machining and metrology.
03 Why IR coating is also expensive
Even if an IR material transmits, the bare surface may not be transparent enough — many IR materials have high refractive index and significant surface reflection. Without an AR coating, a single surface can reflect a large fraction; stacked elements then drop transmission sharply. So IR lenses must be coated, mainly to: ① raise transmission (AR coating reduces reflection, directly affecting brightness, SNR and NETD); ② control the band (3–5 μm MWIR, 8–12 μm / 8–14 μm LWIR, specific gas absorption bands, laser-rangefinder compatible bands); ③ suppress stray light and ghosts (high-reflection surfaces cause internal reflection and false images); ④ improve environmental reliability (outdoor lenses face rain, salt fog, dust, wiping, thermal shock; the front element may need a DLC-class hard protective film).
IR coating is hard because: the longer wavelength changes layer design and process; lens and coating CTEs differ and poor stress control under thermal cycling causes cracking/delamination; broadband AR across the whole 8–12 μm or 8–14 μm band is tough; the front element must also resist wiping and environment. So IR coating is not "just a layer" but a key technology deciding whether a lens truly enters the field.
04 Athermalization: the most underestimated difficulty
Athermalization keeps focus and image quality stable as temperature changes. IR systems work in harsh environments: day-night outdoor swings, vehicle high/low temperature, drone high-altitude cold, industrial heat, firefighting thermal shock, defense field use, and self-heating during long operation. Temperature changes affect two things: the lens material refractive index shifts (changing focal position), and the barrel thermally expands/contracts (changing element spacing and barrel length, also shifting focus). For an IR lens, focus drift brings blurred images, falling edge quality, unstable temperature regions, underestimated small-target peaks and weaker long-range recognition. So a high-end IR lens must perform well not only at room temperature but across the temperature range.
05 What forms does athermalization take?
- Optical athermalization: combine materials (Ge, chalcogenide, ZnSe) so their thermal drifts cancel during design — high difficulty but good stability.
- Mechanical athermalization: use the barrel's thermal expansion to compensate focus drift — demanding on material, dimension and assembly precision.
- Active focusing: motor/piezo or temperature-sensor feedback auto-adjusts focus — flexible but adds volume, power, failure points and calibration complexity.
- Software compensation: algorithms can sharpen/enhance somewhat but cannot truly replace optical focus; if the optical focus has clearly shifted, software only helps marginally.
So high-end IR lenses usually need optics, mechanics, electronics and algorithms working together — to keep transmitting, focusing, low-loss, low-stray, low-drift, stable and accurate across complex environments.